O nás     Inzerce     KontaktSpolehlivé informace o IT již od roku 2011
Hledat
Nepřehlédněte: 2. kolo: Pozoruhodné IT produkty 2020
Správa dokumentů
Digitální transformace
Informační systémy
Hlavní rubriky: Informační systémy, Mobilní technologie, Datová centra, Sítě, IT bezpečnost, Software, Hardware, Zkušenosti a názory, Speciály

Pozoruhodné IT produkty 2020
E-knihy o IT zdarma
Odborné IT konference BusinessIT
Manuál Linux
[Linux manuál]

posix_trace_start, posix_trace_stop: sledovat start a stop (TRACING)

Originální popis anglicky: posix_trace_start, posix_trace_stop - trace start and stop ( TRACING)

Návod, kniha: POSIX Programmer's Manual

STRUČNĚ

#include <trace.h>
 
 
int posix_trace_start(trace_id_t trid);
 
int posix_trace_stop (trace_id_t trid);
 

POPIS / INSTRUKCE

The posix_trace_start() and posix_trace_stop() functions, respectively, shall start and stop the trace stream identified by the argument trid.
The effect of calling the posix_trace_start() function shall be recorded in the trace stream as the POSIX_TRACE_START system trace event and the status of the trace stream shall become POSIX_TRACE_RUNNING. If the trace stream is in progress when this function is called, the POSIX_TRACE_START system trace event shall not be recorded and the trace stream shall continue to run. If the trace stream is full, the POSIX_TRACE_START system trace event shall not be recorded and the status of the trace stream shall not be changed.
The effect of calling the posix_trace_stop() function shall be recorded in the trace stream as the POSIX_TRACE_STOP system trace event and the status of the trace stream shall become POSIX_TRACE_SUSPENDED. If the trace stream is suspended when this function is called, the POSIX_TRACE_STOP system trace event shall not be recorded and the trace stream shall remain suspended. If the trace stream is full, the POSIX_TRACE_STOP system trace event shall not be recorded and the status of the trace stream shall not be changed.

NÁVRATOVÁ HODNOTA

Upon successful completion, these functions shall return a value of zero. Otherwise, they shall return the corresponding error number.

CHYBY / ERRORY

These functions shall fail if:
EINVAL
The value of the argument trid does not correspond to an active trace stream and thus no trace stream was started or stopped.
EINTR
The operation was interrupted by a signal and thus the trace stream was not necessarily started or stopped.
 
The following sections are informative.

PŘÍKLADY POUŽITÍ

None.

APPLICATION USAGE

None.

RATIONALE

None.

FUTURE DIRECTIONS

None.

SOUVISEJÍCÍ

posix_trace_create() , the Base Definitions volume of IEEE Std 1003.1-2001, <trace.h> Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2003 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html .
2003 IEEE/The Open Group
©2011-2020 BusinessIT.cz, ISSN 1805-0522 | Názvy použité v textech mohou být ochrannými známkami příslušných vlastníků.
Provozovatel: Bispiral, s.r.o., kontakt: BusinessIT(at)Bispiral.com | Inzerce: Best Online Media, s.r.o., zuzana@online-media.cz
O vydavateli | Pravidla webu BusinessIT.cz a ochrana soukromí | pg(9554)